How to Put on a Lace Front Wig?

Preparation:

Wig cap, Human hair wig, Scissors, Scalp protector, Wig adhesive, Small adhesive brush, Blow dryer, Wig clips, Hair clamps, Wig tapeStep 1: Get your wig ready.Wigs enhance your style and beautify your facial features so wear it with confidence. Wash and condition with good care and occasionally take your wig for a visit to the stylist to style it any way you like.Step 2: Do a skin test.Some people are allergic to the chemicals used to keep a wig in place. Do a skin test to determine whether or not you are allergic. First, dab a small amount of liquid adhesive or double-sided wig tape onto the back of your hand. Next, observe the adhesive for at least twenty-four hours. If the skin becomes red or irritated, purchase a hypoallergenic wig tape or adhesive to use instead. If the skin is unaffected, you can safely wear the wig.Step 3: Flatten your hair. The flatter your hair is against your head, the better the wig will look. You can braid short hair into cornrows or mold it against your head using gel and bobby pins. For long hair, first, tie your hair in a low ponytail. Next, wrap the ponytail into a flat bun and secure it with bobby pins. Allow any gel or hairspray to dry before continuing.Step 4: Put on a wig cap.Wig caps, or stocking caps, are soft caps that flatten your hair and help the wig stay in place. Gently pull on the stocking cap, being careful not to disturb your flattened hair. Adjust the cap so that it barely covers your hairline. If you have little to no hair, skip this step. Otherwise, the cap will slide around your head and bunch up under your wig. Make sure all of your hairs are tucked into this cap, even the hairs on the nape of your neck.Step 5: Clean your hairline skin. Wash your skin with a gentle cleanser to ensure the application area is oil-free and blot it dry with a towel. Next, dab some rubbing alcohol on a cotton ball and wipe it along your hairline. This will remove the excess oils on your skin. Spray scalp protector directly on your head to act as a barrier between your skin and the adhesive. Allow the serum to dry completely before continuing. Scalp-protecting serums can be bought at wig supply shops and online.Step 6: Test the fit of the wig.Before you apply any adhesives, you need to make sure the wig fits properly. To do so, place the wig on your head and line it up with your natural hairline. If the wig has tightening straps on the inside, you may need to adjust these for a proper fit. If the wig doesn’t fit and it doesn’t have any tightening straps, contact the manufacturer for help. If you can feel a strong ring of pressure around your scalp, the wig is too tight. Loosen the straps slightly. If the wig slides around when you move your head, the wig is too loose. Tighten the straps.Step 7: Trim the lace. Once your wig fits correctly, you have to trim the lace on the human lace front wigs. This only needs to be done the first time you use your wig, and it does not need to be done if the lace has already been trimmed by the manufacturer. Utilize a couple of clasps to pull the hair far from your face. Next, using sharp pinking shears, trim the lace along your natural hairline. You should leave around 1/8 inch (3 mm) of lace closure. This will just must be done the first time when you wear the wig.Step 8: Remove the wig and set it aside. Carefully pull the wig off, leaving all the clips in, and set the wig on a clean flat surface. Arrange the wig so that it’s easy to see what part goes on the hairline and what part goes on the nape of the neck. If you have to loosen any straps to get the wig off, your wig is too tight.Step 9: Apply wig tape.Cut six to ten small pieces of wig tape. Next, line your hairline with the small pieces of tape by pressing the sticky side against your skin. Use a mirror while you do this to create an even hairline. Once the tape is applied, remove the thick foam padding to reveal the other side of the tape. Make sure all of the pieces are touching. Otherwise, you may have loose gaps in your hairline. Wig tape can be bought at wig supply stores or online.Step 10: Use a liquid adhesive. If you don’t want to use wig tape, you can use a liquid lace adhesive instead. Apply adhesive with the brush to areas onto which the wig will attach. Using the cool air setting, blow-dry the adhesive for about 30 seconds. If you use a soft bond adhesive, allow the glue to dry long enough to become tacky before applying the wig. If you use a hard bond adhesive, you can apply the wig immediately.Step 11: Apply the wig. Carefully pull the wig on. First, adjust the edge of the wig so that the hairlines match. Next, adjust the back of the wig so that it hangs naturally over your hair. Lastly, press the lace of the wig into your adhesive or wig tape. Once you press the lace into the adhesive or wig tape, it’s very hard to remove. Be sure that the wig is perfectly aligned before doing so.Step 12: Style your hair.If your wig is made of human hair bundles, you can use regular brushes, hot styling tools, and hair products. If your wig is synthetic, avoid using regular brushes and hot styling tools. Instead, use a wide-toothed comb or wig brush to adjust your hair.