Getting a flat tire is one of those unfortunate yet inevitable situations that every driver is likely to encounter at some point. Whether you're commuting to work, taking a road trip, or simply running errands around town, a flat tire can happen anytime, anywhere. Knowing how to change a flat tire is an essential skill that can save you time, money, and a lot of frustration. This article will walk you through the steps of changing a flat tire, ensuring you can handle the situation with confidence and ease.
👉 Preparation: What You’ll NeedBefore you even start, it’s important to ensure that your vehicle is equipped with the necessary tools. Here’s what you’ll need:
1. Spare Tire. A properly inflated spare tire, also known as a "donut" or full-sized spare, should always be in your trunk.
2. Jack. This is used to lift your car off the ground.
3. Lug Wrench. Also known as a tire iron, this tool is used to remove the lug nuts holding the wheel in place.
4. Wheel Wedges. These are placed in front of or behind the tires to prevent the car from rolling while you’re working.
5. Owner’s Manual. This will provide specific information about your vehicle, including the correct jack points.
👉 How to Change a Flat Tire on a Car
Step 1. Find a Safe Location. The first step in changing a flat tire is to find a safe and level place to pull over. If you're on a busy road, try to find a wide shoulder or a nearby parking lot. Avoid stopping on a curve or in areas with poor visibility. Turn on your hazard lights to alert other drivers, and set the parking brake to prevent the car from moving.
Step 2. Apply the Wheel Wedges. Once you’ve found a safe spot, place the wheel wedges in front of or behind the tires to keep the car from rolling. If the flat tire is at the front, place the wedges behind the rear tires. If the flat is at the back, place them in front of the front tires.
Step 3. Remove the Hubcap or Wheel Cover. If your car has a hubcap or wheel cover, you'll need to remove it before you can access the lug nuts. Use the flat end of your lug wrench to pry off the hubcap. Some cars have special lug nut covers that need to be unscrewed before the hubcap can be removed.
Step 4. Loosen the Lug Nuts. Before lifting the car with the jack, you'll need to loosen the lug nuts. Use the lug wrench to turn the nuts counterclockwise. Don’t remove them completely just yet—just break the initial resistance so they’re easier to remove once the car is off the ground. If the lug nuts are tight, you may need to use your foot or body weight to apply more force.
Step 5. Position the Jack. Refer to your owner’s manual to locate the correct jack points on your vehicle. These are usually reinforced areas of the frame designed to support the weight of the car. Place the jack under the correct point near the flat tire and begin lifting the car. Make sure the jack is on solid, level ground to prevent it from tipping over. Raise the car until the flat tire is about six inches off the ground.
Step 6. Remove the Lug Nuts and the Flat Tire. Once the car is lifted, you can finish removing the lug nuts. Keep them in a safe place, as you’ll need them to secure the spare tire. With the lug nuts removed, carefully pull the flat tire straight off the wheel hub. Place the flat tire under the car as a safety precaution. If the jack fails, the car will land on the tire rather than the ground, which could prevent injury or damage.
Step 7. Mount the Spare Tire. Take your spare tire and align it with the lug bolts. Push the tire onto the wheel hub until it’s snug against the hub. Start threading the lug nuts by hand, tightening them as much as you can. This helps ensure that the tire is properly centered and mounted on the hub.
Step 8. Tighten the Lug Nuts. With the spare tire in place, use the lug wrench to begin tightening the lug nuts. It’s crucial to tighten the nuts in a star or crisscross pattern rather than going around the wheel in a circle. This ensures even pressure on the wheel and prevents it from wobbling. Tighten the lug nuts as much as possible while the car is still lifted.
Step 9. Lower the Car. Once the lug nuts are secure, carefully lower the car back to the ground by slowly turning the jack in the opposite direction. Once the car is fully grounded, remove the jack and give the lug nuts another good tightening to ensure they’re secure.
Step 10. Replace the Hubcap or Wheel Cover. If you removed a hubcap or wheel cover earlier, put it back on the spare tire. If the spare tire is a “donut” type, which is smaller than a regular tire, the hubcap may not fit. In this case, store the hubcap in your trunk until you have the flat tire repaired and reinstalled.
Step 11. Check the Tire Pressure. Before driving off, check the pressure of the spare tire using a tire pressure gauge. Most spare tires require a higher pressure than regular tires—usually around 60 psi. If the tire pressure is too low, drive carefully to the nearest gas station and inflate the tire to the recommended pressure.
Step 12. Stow the Equipment and Flat Tire. After everything is secured, pack away your tools, jack, and wheel wedges. Place the flat tire in your trunk. Don’t forget to take it to a mechanic or tire shop as soon as possible to get it repaired or replaced.
Step 13. Drive Carefully. Spare tires, especially “donuts,” are not designed for long distances or high speeds. They are temporary solutions meant to get you to a tire repair shop. Avoid driving over 50 mph, and try not to exceed 50-70 miles on the spare tire. If your spare is a full-sized tire, you can drive normally, but it’s still a good idea to get your original tire repaired or replaced soon.
💬 Final ThoughtsChanging a flat tire is a skill every driver should have. While it may seem daunting at first, with the right tools and knowledge, you can confidently change a tire and get back on the road in no time. Remember to always stay safe, work carefully, and if you ever feel uncomfortable or unsure, don’t hesitate to call for roadside assistance.
Want more videos all about auto?
Subscribe to our YouTube channel 👉Cartech Home