The Design
My house has a lot of traditional pieces of furniture. My mother and grandmother loved to pass down furniture. I believe you should buy quality furniture pieces but the only problem with that philosophy is that they never die! So I am slowly transitioning to a cleaner aesthetic one tiny corner at a time.
One of the ways to mix traditional and modern aesthetics is to take a modern shape and use colors and finishes that blend with your traditional piece. That is what I decided to do with my cube table.
I painted the entire cube gold and created a mosaic top using marbleized blue paper and epoxy to give it a nice glassy top. This was designed to coordinate with a blue leather wing back I have in my family room with brass nail heads. Contrasting colors would work just as well – in fact I am still hunting for the perfect pillow to put in the chair to add a pop of color.
The Materials
- 1 IKEA PS 2520 plant stand table (found in the garden/plant section)
- 2′x4′ thin plywood sheet cut to size of top – I traced around the plastic top to get the right size. You could probably use the plastic top if you primed it with a paint meant for plastic but I did not want to experiment with the epoxy finish I was afraid it might make the paint bubble off of the plastic – if you try it and it works let us know!!!)
- 5 sheets of a decorative paper of your choice (this is more than you will need but I always buy a little extra to save a second trip to the store)
- Mod Podge or other clear drying glue
- Spray paint in the color of your choice – I used Design Masters Gold
- Pour on epoxy – this is the KEY to creating a table top that will withstand daily use
- Plastic cup to mix epoxy
- Wooden craft stick for mixing and spreading (you could also use a plastic knife – the box suggests spreading with strong paper but I did not find index cards sturdy enough)
- Small finish nails
- Spackle or wood filler
The Process
- Watch the video first, these instructions are meant to help you remember the order or answer any additional question
- Assemble the cube
- Cut out the wooden top and attach it with the cube – attach it to the cube with the small finish nails – sink the nails and fill the holes
- Paint the entire thing with 2-3 coats of gold paint
- Cut out the diamonds from the paper using these measurements
- I used a paper cutter but scissor would do – I cut through 3 pieces at a time to save time
- Cut out the squares
Draw lines through the center of the top to help keep your design centered - I laid out the entire top before I stuck anything down to see if I needed to make any adjustments
- Here is a guide to help you lay out your top
Glue down your pieces – they do not have to be well attached because the epoxy will hold them in place - Mix your epoxy following the directions on the box carefully
Pour out the resin spreading it out around the top – not into one pool in the middle - Use the wooden stick to spread the epoxy out evenly – it does not spread itself so if it is uneven when you stop working with it, it will dry that way
- Watch the epoxy for the first 15 minutes or so – blow lightly on any bubbles to pop and remove them, clean up any drips that go over the side
- Let the table cure for at least 48 hours before touching or using
Watch the video if you are confused about any part of this process, or comment and I will respond!
The Outcome
I love this light weight table, it is easy to move around but packs a big design punch. It may sound like this is complicated but it really was cutting out paper, gluing it down and pouring something on top! My kids keep touching the surface to try to figure how it looks so much like glass. Create your own mosaic pattern, let your imagination go wild. If you do send us a photo I would love to see it!
The Budget
$24.99 –IKEA PS 2510 (It is usually $29.99 but I found it marked down)
$13.98 - Epoxy
$2.95 –5 Pieces of scrapbook paper at 59 cents each
$3.79- Gold spray paint
$6.00 -Small piece of 1/4 inch plywood
$0.00 – I had the Mod Podge, finish nails and wood filler
TOTAL: $51.71